User guide

Connecting the Pressac Gateway to AWS IoT Core

In this guide, we’ll show you how to connect the Pressac EnOcean Gateway running Pressac Gateway Software to AWS IoT Core. This multi-step process includes:

  • Configuring AWS IoT Core
  • Registering your IoT device
  • Configuring the Pressac EnOcean Gateway to send device data to AWS IoT Core

Step 1: Prerequisites

You should have the following items/actions ready before beginning the process:

  • Setup your AWS IoT Console
  • Register a device in the registry and download its certificates
  • Pressac EnOcean Gateway Ethernet (E) or Ethernet, LTE and WiFi (ELW) running firmware version or above.
  • Pressac EnOcean device compatible with the Pressac EnOcean Gateway e.g. CO2, Temperature and Humidity Sensor (EnOcean Radio Protocol Version).
  • Computer running either Windows or OSX
  • Suitable web browser to connect to both AWS IoT Core and the Pressac EnOcean Gateway configuration pages.

Step 2: Prepare your Device

Plug in one end of the Ethernet cable into your network point and plug the opposite end of the cable into the Ethernet port on the Pressac EnOcean gateway.

Connect the EnOcean antenna along by screwing it onto the connection on the Pressac EnOcean Gateway taking care not to cross thread or bend. If your gateway supports LTE and WiFi attach the antennas for these as well.

Connect your Pressac EnOcean Gateway’s power supply. Connecting the power supply will boot up the Pressac EnOcean Gateway and you will see the products LED start blinking. The Pressac EnOcean Gateway will take a few seconds to initialise.

Next you need to find the IP Address of the Pressac EnOcean Gateway. The most common way of doing this is to check your routers list of connected devices. If this is not possible the following alternative methods can be used:

  1. Windows: The Pressac EnOcean Gateway announces itself over Universal Plug and Play (UPnP) and can be found in the “Gateways” or “Other Devices” section of the Windows Network area. To find this area click “Start” search for “Network” and click “View network connected computers and devices”. Double clicking a gateway from here will open up the web-ui.
  2. Mac: The Pressac EnOcean Gateway can be discovered using Bonjour. One of the easiest ways of using this method is to open “Safari”, go to “Preferences” then “Advanced” and tick “Include Bonjour in the Bookmarks menu”. Then close Preferences navigate to “Bookmarks” and you will now see all your networked Bonjour devices including the Pressac EnOcean Gateway.

Now you have the IP Address you can use it to access the Pressac EnOcean Gateways web interface. Launch your chosen web browser and type http://<your-ip> e.g.
This will display the Pressac EnOcean Gateway’s first boot wizard. Follow the steps on the wizard to set up your Pressac EnOcean Gateway for the first time.

Connecting the Pressac Gateway to AWS IoT Core

Step 3: Add Your Devices to the Pressac EnOcean Gateway

To learn-in a new device click “– Add Devices” in the EnOcean sub-menu on the Pressac EnOcean Gateway web-interface and then click “Start”.

Connecting the Pressac Gateway to AWS IoT Core

This will initiate a 60 second countdown, during these 60 seconds the Pressac EnOcean Gateway will listen for the learn telegrams of devices in range of the Pressac EnOcean Gateway. This process can be cancelled by clicking “Cancel” and re-started for another 60 second duration by clicking “Search” again.

Ensure the Pressac EnOcean Gateway is listening for learn telegrams and press the “Learn” button on your Pressac device. To locate the learn button for your device please consult your individual device manual. Once pressed a new device entry will now appear in a table with the following columns:

Last Seen – The Date and Time the Pressac EnOcean Gateway last received a telegram from the device

Device ID – The unique identification number of the device

EEP – EnOcean Equipment Profile used by the device.

Security – Security enabled on the device Yes / No

dBm – Signal strength of the device to the gateway

Action – The action column contains a menu containing options to EDIT AND ADD and DELETE the device.

Connecting the Pressac Gateway to AWS IoT Core

Click on “Edit and add” from the menu under the Action column as shown in the above image. To edit the device a new screen will appear as shown in the image below.

Connecting the Pressac Gateway to AWS IoT Core

The only required field is the device name, it is advised to use a device name which resembles the function and location of the device. e.g. if your device is a CO2, Temperature and Humidity Sensor and it is situated in Classroom 1, your Device Name could be “Classroom1-CO2-Temperature-Humidity”.

Other optional properties include the location of your physical device. Please note that only characters A-Z, numbers, ‘_’ and ‘-‘ are permitted to be used in any of these fields.

Once you have specified your desired device name and any of the other optional properties click “Save” at the bottom of the screen to save the entry.

You can now navigate to the devices page and see the device along with its last state. Repeat step 2 until all your desired devices are learnt-in to the Pressac EnOcean Gateway.

Step 4: Connect Pressac EnOcean Gateway to Your AWS IoT Core Device

Navigate to the AWS IoT Core connection page by clicking “- AWS IoT” in the Connections sub-menu on the Pressac EnOcean Gateway web-interface and then change the AWS IoT Connection from “OFF” to “ON”.

Connecting the Pressac Gateway to AWS IoT Core

Once you have switched “ON” the connection you will need to input the Client ID, Topics and Endpoint as well as upload your certificates from the device you made earlier.

After inputting your connection details and uploading your certificates select which data you would like to be included in the payload and click “Save”. The AWS IoT connection status will now change to “Connected”.

Connecting the Pressac Gateway to AWS IoT Core